Victron SmartSolar MPPT 100-20-(12-24-48V)

Victron SmartSolar MPPT 100-20-(12-24-48V)

Bluetooth Smart built-in

The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.

VE.Direct - For a wired data connection to a Color Control GX, other GX products, PC or other devices.

Ultra-fast Maximum Power Point Tracking (MPPT)

Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers.

Load output

Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage (48 V model: interface with a relay). Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.

Battery Life: intelligent battery management

When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no

regular full recharge) will destroy a lead-acid battery within weeks or months.

The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the

full 100 %. From that point onwards, the load disconnect level will be modulated so that a nearly 100 % recharge is achieved about once every week.

Programmable battery charge algorithm - See the software section on our website for details.

Day/night timing and light dimming option - See the software section on our website for details.

Internal temperature sensor - Compensates absorption and float charge voltage for temperature.

Optional external battery voltage and temperature sensing via Bluetooth

A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers.

Fully discharged battery recovery function

Will initiate charging even if the battery has been discharged to zero volts.

Will reconnect to a fully discharged Li-ion battery with integrated disconnect function.

Specifications:

Battery Voltage: 12/ 24V / 48V Auto Select

Rated charge current: 20A

Nominal PV Power Input 12V: 290W

Nominal PV Power Input 24V: 580W

Nominal PV Power Input 48V: 1160W

If more PV power is connected, the controller will limit input power and The PV voltage must exceed Vbat + 5V for the controller to start. Thereafter the minimum PV voltage is Vbat + 1V.

Max. PV short circuit voltage: 20A

Automatic load disconnect: Yes

Maximum PV open circuit voltage: 100V

Maximum efficiency: 98%

Self-consumption – load on: 26 / 20 / 19 mA

Self-consumption – load off: 10 / 8 / 7 mA

Charge voltage 'absorption': 14,4 V / 28,8 V / 57,6 V (adj.)

Charge voltage 'float': 13,8 V / 27,6 V / 55,2 V (adj.)

Charge algorithm: multi-stage adaptive

Temperature compensation: -16 mV / -32 mV / Degree C.

Continuous / peak load current: 20A / 20A / 1A

Low Voltage load Disconnect: 11,1 V / 22,2 V / 44,4 V or 11,8 V / 23,6 V / 47,2 V or Battery Life algorithm

Low Voltage load Reconnect: 13,1 V / 26,2 V / 52,4 V or 14 V / 28 V / 56 V or Battery Life algorithm

Protection: Output short circuit / Over temperature

Operating temperature: -30 to +60°C (full rated output up to 40°C)

Humidity: 95%, non-condensing

Data communication port: VE.Direct

Encloser Colour: Blue (RAL 5012)

Power terminals: 6 mm² / AWG10

Protection category: IP43 (electronic components), IP22 (connection area)

Weight: 0,65kg

Dimensions (h x w x d) in mm: 100 x 131 x 60 mm

Safety Standards: EN/IEC 62109-1, UL 1741, CSA C22.2